ESP32 AD输入

• 0~3.3V
• 12bit

https://randomnerdtutorials.com/esp32-adc-analog-read-arduino-ide/

// Potentiometer is connected to GPIO 34 (Analog ADC1_CH6) 
const int potPin = 34;

// variable for storing the potentiometer value
int potValue = 0;

void setup() {
  Serial.begin(115200);
  delay(1000);
}

void loop() {
  // Reading potentiometer value
  potValue = analogRead(potPin);
  Serial.println(potValue);
  delay(500);
}

Fast sampling from analog input

The first part of the OScope project is to implement the Arduino sketch to read the input values from an analog pin. In this article will describe how to achieve a reliable sampling of analog signals up to 615 KHz using some advanced techniques.

Arduino provides an convenient way to read analog input this using the analogRead() function. Without going into much details the analogRead() function takes 100 microseconds leading to a theoretical sampling rate of 9600 Hz. You can read more about this topic here.

The following piece of code takes 1000 samples using the analogRead() calculates some statistics.

void setup()
{
  Serial.begin(115200);
  pinMode(A0, INPUT);
}

void loop()
{
  long t0, t;

  t0 = micros();
  for(int i=0; i<1000; i++) {
    analogRead(A0);
  }
  t = micros()-t0;  // calculate elapsed time

  Serial.print("Time per sample: ");
  Serial.println((float)t/1000);
  Serial.print("Frequency: ");
  Serial.println((float)1000*1000000/t);
  Serial.println();
  delay(2000);
}

This code gives 112us per sample for a 8928 Hz sampling rate.

So how can we increase sampling rate?

Speedup the analogRead() function

We now need a little more details. The ADC clock is 16 MHz divided by a 'prescale factor'. The prescale is set by default to 128 which leads to 16MHz/128 = 125 KHz ADC clock. Since a conversion takes 13 ADC clocks, the default sample rate is about 9600 Hz (125KHz/13). Adding few lines of code in the setup() function we can set an ADC prescale to 16 to have a clock of 1 MHz and a sample rate of 76.8KHz.

#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))

void setup()
{
  sbi(ADCSRA, ADPS2);
  cbi(ADCSRA, ADPS1);
  cbi(ADCSRA, ADPS0);
  ...

The real frequency measured with the test program is 17us per sample for a 58.6 KHz sampling rate.

The following table shows prescale values with registers values and theoretical sample rates. Note that prescale values below 16 are not recommended because the ADC clock is rated.

Prescale	ADPS2 ADPS1 ADPS0	Clock freq (MHz)	Sampling rate (KHz)
2	0 0 1	8	615
4	0 1 0	4	307
8	0 1 1	2	153
16	1 0 0	1	76.8
32	1 0 1	0.5	38.4
64	1 1 0	0.25	19.2
128	1 1 1	0.125	9.6

Interrupts

A better strategy is to avoid calling the analogRead() function and use the 'ADC Free Running mode'. This is a mode in which the ADC continuously converts the input and throws an interrupt at the end of each conversion. This approach has two major advantages:

1. Do not waste time waiting for the next sample allowing to execute additional logic in the loop function.
2. Improve accuracy of sampling reducing jitter.

In this new test program I set the prescale to 16 as the example above getting a 76.8 KHz sampling rate.

int numSamples=0;
long t, t0;

void setup()
{
  Serial.begin(115200);

  ADCSRA = 0;             // clear ADCSRA register
  ADCSRB = 0;             // clear ADCSRB register
  ADMUX |= (0 & 0x07);    // set A0 analog input pin
  ADMUX |= (1 << REFS0);  // set reference voltage
  ADMUX |= (1 << ADLAR);  // left align ADC value to 8 bits from ADCH register

  // sampling rate is [ADC clock] / [prescaler] / [conversion clock cycles]
  // for Arduino Uno ADC clock is 16 MHz and a conversion takes 13 clock cycles
  //ADCSRA |= (1 << ADPS2) | (1 << ADPS0);    // 32 prescaler for 38.5 KHz
  ADCSRA |= (1 << ADPS2);                     // 16 prescaler for 76.9 KHz
  //ADCSRA |= (1 << ADPS1) | (1 << ADPS0);    // 8 prescaler for 153.8 KHz

  ADCSRA |= (1 << ADATE); // enable auto trigger
  ADCSRA |= (1 << ADIE);  // enable interrupts when measurement complete
  ADCSRA |= (1 << ADEN);  // enable ADC
  ADCSRA |= (1 << ADSC);  // start ADC measurements
}

ISR(ADC_vect)
{
  byte x = ADCH;  // read 8 bit value from ADC
  numSamples++;
}

void loop()
{
  if (numSamples>=1000)
  {
    t = micros()-t0;  // calculate elapsed time

    Serial.print("Sampling frequency: ");
    Serial.print((float)1000000/t);
    Serial.println(" KHz");
    delay(2000);

    // restart
    t0 = micros();
    numSamples=0;
  }
}

If you want to learn more on ADC Free Running mode and tweaking ADC register you can look at the following pages.

‎AVR Guide - Analog Inputs Instructables - Girino - Fast Arduino Oscilloscope Instructables - Arduino Audio Input Arduino Forum - Faster Analog Read